Differentail Bearing and Race-Sides

1947-62
Differential Bearing & Race-Sides 1947-62
Differential Bearing / Race-Sides 1947-62 Chevrolet / GMC ∙ Cone Bore = 1.5" = 38.1 mm
∙ Cone Width = 1.01" = 25.6 mm
∙ Cup Bore = 3 " = 76.2 mm
∙ Cup Length = 0.75" = 19.05 mm
∙
€ 52,⁹⁵
1955-72
Rear End Pinion Bearing-Rear-1/2 ton 1955-72
Rear End Pinion Bearing-Rear-1/2 ton 1955-72

∙ Bearing = Bore=1.4375", Length=1.125", Radius=0.14"
∙ Rice-sides = Outer Diameter=3", Length=0.9063", Radius=0.125"
∙
∙ Buitenwerkse maat = 76.20 mm
∙ Binnenwerkse maat = 36.51 mm
€ 39,⁹⁵
1960-2013
Differential Pinion Bearing / Race 1960-2013
Differential Pinion Bearing / Race
1960-2013 Chevrolet 1965-2013 GMC

Lager maten
Cone Bore (Inch) 1.3125
Cone Bore (MM) 33.3380
Cone Length (Inch) 0.8750
Cone Length (MM) 22.2250
Cone Radius (Inch) 0.0310
Cone Radius (MM)…
€ 39,⁹⁵
1935-54
Rear End Rear Pinion Bearing 1935-54
REAR END REAR PINION BEARING 1935-54

Diameter Buitenkant = 79.4 mm

Diameter binnenmaat = 46.1 mm

breedte van buitenkant = 19 mm
€ 99,⁹⁵
1939-62
Rear End Vent Tube 1939-62
REAR END VENT TUBE 1939-62

Also used on 1957-62 close ratio 3 speed. and 1957-62 4 speed. transmission. This is a necessary part to keep out dirt as well as a pressure relief valve.
€ 22,⁹⁵
1947-91
Rear Axle Locks 1947-91
REAR AXLE LOCKS 1947-91

Fits 1947-59 1/2 ton without positrac,

1960-87 1/2 ton, and 88-91 R/V series Blazer & Suburban 1 per axle
€ 8,⁹⁵
1965-2003
Differential Pinion Bearing / Race
DIFFERENTIAL PINION BEARING / RACE
88.90 X 19.05 MM

Cup Bore (Inch) 3.5000
Cup Bore (MM) 88.9000
Cup Length (Inch) 0.7500
Cup Length (MM) 19.0500
Cup Radius (Inch) 0.1250
Cup Radius (MM) 3.1750
Part Description Taper Bearing Cup
€ 24,⁹⁵
1955-64
Differential Rebuild Kit GM55 1955-64
Differential Rebuild Kit GM55. 1955-64 Chevrolet Axel

∙ 1955-64 Chevrolet GM55 axel
∙ Outer Pinion Bearing / race
∙ inner Pinion Bearing / Race
∙ Carrier Bearing / Races
∙ Pinion Nut
∙ Pinion Seal
∙ Crush Sleeve
∙…
€ 215,⁹⁵
GM8.5"- 28 spline
Differential Rebuild Kit GM85. 1979-86
Differential Rebuild Kit GM85.
1979-86 Chevrolet Axel

∙ Fits
∙ GM 8.5" Rear 28 Spline
∙ Uses Koyo bearings and races
∙ Included are carrier bearings and races, pinion bearings and races, pinion seal, pinion nut, crush…
€ 215,⁹⁵
8:875
Differential Rebuild Kit. Rear; 12 Bolt; with GM 8.875 Axle
Differential Rebuild Kit. Rear; 12 Bolt; with GM 8.875 Axle.Master Bearing Kit for GM 8:875 Axle, ;

Includes

∙ Koyo Bearings (Carrier, Front and Rear Pinion, Pilot where applicable), Brush,
∙ Cover Gasket (or RTV), Crush…
€ 199,⁹⁵
1955-62
Rear End Pinion Bearing-Front 1955-62
REAR END PINION BEARING-FRONT 1955-62

Foto 1 Afmetingen

Cone Bore (Inch) 1.3125
Cone Bore (MM) 33.3380
Cone Length (Inch) 1.0938
Cone Length (MM) 27.7830
Cone Radius (Inch) 0.0310
Cone Radius (MM) 0.7870
Part Description Taper…
€ 69,⁹⁵
1942-82
Main / Output Shaft Bearing. 72 mm x 35 mm
MAIN / OUTPUT SHAFT BEARING. 72 MM X 35 MM
1942-82 CHEVROLET / 1951-86 FORD

Bearing Inside Diameter (IN) 1.378
Bearing Inside Diameter (MM) 35.001
Bearing Outside Diameter (IN) 2.835
Bearing Outside Diameter (MM) 72.009
Length…
€ 49,⁹⁵
80 x 35
Main / Output Shaft Bearing. 80 mm x 35 mm
MAIN / OUTPUT SHAFT BEARING. 80 MM X 35 MM
1955-89 CHEVROLET / 1945-87 FORD

Bore (IN) 1.378 = 35.00 mm
Outside Diameter (IN) 3.149 = 79.99 mm
Width (IN) 0.826 = 20.98 mm
€ 52,⁹⁵
GM 8.2" a 3.55 Ratio
Achter as overbrenging 3.55 :1 Ring & pinion 47-54 GM
High performance Yukon Ring & Pinion gear set for GM 8.2" in a 3.55 ratio

Product Details

Yukon Gear & Axle high-performance ring and pinion gear sets are the benchmark of quality in the automotive gear industry. Yukon engineers…
€ 555,⁰⁰
1963-82
Differential Cross Pin .Rear; GM 8.875" (12 Bolt) 1963-82
Differential Cross Pin .Rear; GM 8.875" (12 Bolt) 1963-82 Chevrolet Truck

∙ 1963-82 Chevrolet Differential
∙ GM 8.875" -- 12 bolt --
∙ Length 5.39" / Lengte = 137 mm
∙ Thickness 0.807" / Dikte = 20.5 mm
€ 29,⁹⁵
28 Spool
9 Inch Fits Ford Rear End Overhaul Kit, 28 Spool Spline
9 Inch Fits Ford Rear End Overhaul Kit, 28 Spool Spline

∙ This 9" Ford overhaul kit includes:
∙ pinion pilot, pinion shaft, pinion nut, pinion seal, gasket, shims, crush collar, sealant, gear marking grease, brush and…
€ 149,⁹⁵
31 Spool
Rear End Overhaul Kit, 31 Spool Spline, Fits Ford 9 Inch
Rear End Overhaul Kit, 31 Spool Spline,
Fits Ford 9 Inch

∙ For a 31 Spool spline
∙ This 9" Ford overhaul kit includes:
∙ pinion pilot, pinion shaft, pinion nut, pinion seal, gasket, shims, crush collar, sealant, gear…
€ 149,⁹⁵